Hydrotech 6700 XTR Valve Downflow Automatic Water Softeners User Manual

6700XTR DownowService Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference

Page 10Master Programming Mode Flow ChartCAUTION: Before entering Master Programming, please contact your local professional water dealer.NOTE: Depend

Page 11Master Programming Mode Flow ChartCAUTION: Before entering Master Programming, please contact your local professional water dealer.NOTE: Depend

Page 12Master Programming ModeCAUTION: Before entering Master Programming, please contact your local professional water dealer.When the Master Program

Page 13Master Programming ModeCAUTION: Before entering Master Programming, please contact your local professional water dealer.Regenerant Flow This pr

Page 1Master Programming ModeCAUTION: Before entering Master Programming, please contact your local professional water dealer.Capacity Safety Factor

Page 15Regeneration Cycle Step Programming This program step programs the Regeneration Cycle step times 1 through 5. Please refer to the chart below f

Page 16a. Timed Auxiliary Relay Output Window (Start & End Time Setting) This option setting consists of two displays. The rst display sets the t

Page 17User Programming Mode & Flow ChartNOTE: Depending on current option settings, some displays cannot be viewed or set. Enter User Mode — Pre

Page 18Diagnostic Programming Mode Flow ChartEntering Diagnostic Mode:Press and release the “D” button.Press the Extra Cycle button once per display u

Page 1Diagnostic Programming ModeNOTE: Depending on current option settings, some displays cannot be viewed.Overview Diagnostic Mode The current Diag

Job Specication Sheet ...

Page 206700XTR Powerhead Assembly61501-6700_REVC

Page 216700XTR Powerhead Assembly Item No. Quantity Part No. Description 1 ...1 ...15-0 ...Drive

Page 22Control Valve Assembly61500-6600-6700_DF_REVB

Page 23Control Valve Assembly Item No. Quantity Part No. Description 1 ...1 ...1700-10 ...

Page 2Meter Assembly Item No. Quantity Part No. Description 1 ...1 ...13874 ...Cap, Meter, Elec

Page 25Bypass Valve Assembly, Non-Metallic Item No. Quantity Part No. Description 1 ...2 ...13305 ...

Page 26Bypass Valve Assembly, Brass Item No. Quantity Part No. Description 1 ...1 ...40614 ...By

Page 272300 Safety Brine Valve Item No. Quantity Part No. Description 1 ...1 ...60027-00 ...Safety Br

Page 282310 Safety Brine Valve Item No. Quantity Part No. Description 1 ...1 ...19645 ...Body, S

Page 2Troubleshooting - TimerIf an error is detected, an error screen will alternate with the main display screen every few seconds, and the LED ligh

Page 3Job Specication SheetNOTE: Some options may not be available depending on valve model or other options chosen.Circle and/or Fill in the Appropr

Page 30Troubleshooting - Control ValveProblem Cause Correction1. Water conditioner fails to regenerate.A. Electrical service to unit has been interru

Page 31Troubleshooting - Control ValveProblem Cause Correction8. Softener fails to draw brine. A. Drain line ow control is plugged.A. Clean drain li

Page 32Water Conditioner Flow DiagramsService PositionBackwash Position

Page 33Water Conditioner Flow DiagramsBrine/Slow Rinse PositionRapid Rinse

Page 3Water Conditioner Flow DiagramsBrine Tank Fill Position

Page 35Valve Wiring Diagram213_REVA

Page 36Service AssembliesAir Check:60002-3 ... Air Check, #500, 3” LongBrine Line Flow Control:60022-12 ... BLFC, .125 GPM, 5000/5600/000

Page 37Notes

Page 38Notes

Page 3Notes

Page General Residential Installation Check ListWater Pressure A minimum of 20 psi water pressure is required for regeneration valve to operate effec

P/N 2132 Rev. B

Page 5Timer OperationValve State: INI (Initializing) INI will display on the screen for 30 to 5 seconds when initializing after a power failure re

Page 6Timer OperationRegeneration: • A time initiated control valve regenerates when the number of programmed days has been reached • A ow in

Page 7Timer OperationQueued Regeneration (RGQ)From the display screen, while the unit is in service, hold down the Extra Cycle button until “RGQ” disp

Page 8Master Programming Mode Flow ChartCAUTION: Before entering Master Programming, please contact your local professional water dealer.NOTE: Dependi

Page Master Programming Mode Flow ChartCAUTION: Before entering Master Programming, please contact your local professional water dealer.NOTE: Dependi